Minwax® Wood Finish™

Overview

Minwax® Wood Finish™ is a penetrating oil-based wood stain, which provides beautiful rich color that enhances the natural wood grain. It applies easily and penetrates deep into the pores of the wood.

  • Available in 28 beautiful colors.
  • Can be used to add beauty to any bare or stripped wood surface.
  • It is ideal for staining unfinished wood furniture, cabinets, wood door, trim, molding and hardwood floors.
  • Minwax® Wood Finish™ is also available in an aerosol can.

تفاصيل المنتج

أداة التطبيق natural bristle brush, cloth or foam applicator
منطقة التطبيق الأسطح الخشبية
إعادة الدهان 4-6 hours
وقت الجفاف 8 ساعات
التنظيف نفط
معدل الفرد 150 sq. ft. per quart
عدد الأوجه 1 coat. To darken the color, apply a second coat after 4-6 hours.
unfinished wood furniture, woodwork, doors, hardwood floors, cabinets, accessories

FOR INTERIOR USE ONLY

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and clean up. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

APPLICATION FOR SURFACES OTHER THAN HARDWOOD FLOORS

SURFACE PREPARATION:

  • Surface must be dry, clean, and free of dirt, grease, glue, and existing coatings before staining.
  • Sand the wood in the direction of the grain using fine-grade sandpaper (#220) until smooth.
  • Remove all sanding dust.
  • To ensure uniform acceptance of stain color and beautiful results, pretreat the wood with Minwax® Pre-Stain Wood Conditioner following label directions.

PRODUCT PREPARATION AND COLOR TESTING:

  • Stir stain thoroughly before and occasionally during use. Do not thin.
  • Always test stain on an inconspicuous area of the wood to verify desired color.

STAIN APPLICATION:

  • Apply stain in the direction of the grain with a brush or clean cloth.
  • Allow the stain to penetrate 5-15 minutes to achieve desired color. The more time the stain is allowed to penetrate, the richer and darker the color will be.
  • Remove stain that has not absorbed into the wood with a clean cloth. Wipe in the direction of the grain, while blending light and dark areas to obtain uniform color. DO NOT ALLOW STAIN THAT HAS NOT PENETRATED INTO THE WOOD TO DRY ON THE WOOD SURFACE.
  • To darken the color, apply a second coat after 4-6 hours, repeating directions above. DO NOT SAND BETWEEN COATS OF STAIN.

CLEAR FINISH APPLICATION:

Allow stain to dry for a minimum of 8 hours (dry time may be extended due to high humidity, low temperatures, or inadequate ventilation). Complete your project by applying a Minwax® clear protective finish, following label directions.

APPLICATION FOR HARDWOOD FLOORS

SURFACE PREPARATION:

  • Whether you have a bare wood floor or a floor that already has a finish on it, you will need to sand the floor to prepare it for staining and finishing. Rent or purchase a floor sander and follow the sander manufacturer’s directions to sand the surface down to bare wood, ending with 100 grit sandpaper or equivalent.
  • Remove all sanding dust. Stir stain thoroughly before and occasionally during use. Do not thin. Test stain on an inconspicuous area of the wood to verify desired color.

STAIN APPLICATION:

  • Apply the stain to the floor using a clean cloth, following the direction of the grain. Work in small sections, approximately three-foot wide, running the entire length of the floor.
  • Allow the stain to penetrate for up to 5 minutes, then wipe off any stain that has not absorbed into the wood, using a clean cloth. The more time the stain is allowed to penetrate, the richer and darker the color will be. DO NOT ALLOW STAIN THAT HAS NOT PENETRATED INTO THE WOOD TO DRY ON THE WOOD SURFACE.
  • To darken the color, apply a second coat after 4-6 hours, repeating directions above. DO NOT SAND BETWEEN COATS OF STAIN.

CLEAR FINISH APPLICATION:

Allow stain to dry for a minimum of 8 hours (dry time may be extended due to high humidity, low temperatures, or inadequate ventilation). Complete your project by applying a Minwax® clear protective finish such as Minwax® Super Fast-Drying Polyurethane for Floors,Minwax® Ultimate Floor Finish , or Minwax® Fast-Drying Polyurethane , following label directions.

  • Recommended finishes include Minwax® Fast-Drying Polyurethane or ورنيش زيتي. Slight ambering may occur when these clear finishes are applied over light or really dark colored stains.
  • Minwax® Polycrylic® Protective Finish is also recommended, especially over the following Minwax® Wood Finish™ colors: Pickled Oak, Weathered Oak, Classic Gray, Ebony, True Black and Simply White. Polycrylic® shound NOT be used over any Red Mahogany stain.
  • Always spot test on an inconspicuous area to ensure satisfactory results.

COVERAGE: Approximately 150 square feet per quart.

CLEANUP: Use mineral spirits or paint thinner following manufacturer’s safety instructions.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

Colors

The colors shown are for reference purposes only. They have been reproduced using digital production techniques. Always test stain on a hidden area of the wood to verify desired color.

Stain adds beauty and color to the wood surface. Be sure to protect your project by applying a clear protective finish, following label directions.

Recommended finishes include Minwax® Fast Drying Polyurethane or ورنيش زيتي. Slight ambering may occur when these finishes are applied over light or really dark colored stains.

*Minwax® Polycrylic® Protective Finish is also recommended, especially over the following Minwax® Wood Finish™ colors: Pickled Oak, Weathered Oak, Classic Gray, Ebony, True Black and Simply White. Polycrylic® should NOT be used over any Red Mahogany stain.

NATURAL 209
NATURAL 209
GOLDEN OAK 210B
GOLDEN OAK 210B
PROVINCIAL 211
PROVINCIAL 211
RED OAK 215
RED OAK 215
PURITAN PINE 218
PURITAN PINE 218
IPSWICH PINE 221
IPSWICH PINE 221
SEDONA RED 222
SEDONA RED 222
COLONIAL MAPLE 223
COLONIAL MAPLE 223
SPECIAL WALNUT 224
SPECIAL WALNUT 224
RED MAHOGANY 225
RED MAHOGANY 225
EARLY AMERICAN 230
EARLY AMERICAN 230
GUNSTOCK 231
GUNSTOCK 231
RED CHESTNUT 232
RED CHESTNUT 232
ENGLISH CHESTNUT 233
ENGLISH CHESTNUT 233
CHERRY 235
CHERRY 235
FRUITWOOD 241
FRUITWOOD 241
GOLDEN PECAN 245
GOLDEN PECAN 245
PICKLED OAK 260 *
PICKLED OAK 260 *
WEATHERED OAK 270 *
WEATHERED OAK 270 *
CLASSIC GRAY 271 *
CLASSIC GRAY 271 *
HONEY 272
HONEY 272
ESPRESSO 273
ESPRESSO 273
TRUE BLACK 274 *
TRUE BLACK 274 *
SIMPLY WHITE 275 *
SIMPLY WHITE 275 *
DRIFTWOOD 2126
DRIFTWOOD 2126
DARK WALNUT 2716
DARK WALNUT 2716
EBONY 2718 *
EBONY 2718 *
JACOBEAN 2750
JACOBEAN 2750
  • 5 نجوم
  • 4 نجوم
  • 3 نجوم
  • 2 نجوم
  • 1 نجوم

متوسط تصنيف النجوم: 0.0 out of 5 (0 تصويت)

If you finish the payment today, your order will arrive within the estimated delivery time.

التعليقات

لا يوجد تعليقات بعد.

كن أول من يقوم بالتعليق على “Minwax® Wood Finish™”

لن يتم نشر عنوان بريدك الإلكتروني. الحقول الإلزامية مشار إليها بـ *

Shopping cart